Lighting Controls_Photo Controllers_Lighting Relays_Power Handling Controls_Timers_Digital Timers
| CAP MLC-8, 8a, 8T and 8aT Lighting Relays The MLC-8 Master Lighting Controller is the best device for controlling up to eight HID lights from one time-clock or controller. You run 40 amp, 240 volt power into the MLC-8, and all of the outlets are controlled by one 120 volt "trigger cable". You can plug the "trigger cable" into a standard 24 hour timer or lighting controller. The MLC-8 features eight standard 240 volt style (NEMA 6-15) outlets, which your ballasts are plugged into. The MLC-8a uses 120 volt style (NEMA 5-15) outlets which allows for running your ballasts at 240 volts without having to change out your ballast power cord. An integrated timer option is available which replaces the "trigger cable", allowing you to control your MLC with a built-in time clock. NOTE: Make sure ballasts are wired/configured for 240 Volt operation before energizing them. Rated at 40 amps @ 240 volts. The “D” models with dual trigger cables allow the user to control half of the lights independent of the other half when plugged into two different timers. |
| CAP MLC-4 Lighting Relays |
| CAP MLC-4 Lighting Relays The MLC-4 Master Lighting Controller is the best device for controlling up to four HID lights from one time-clock or controller. You run 30 amp, 240 volt power into the MLC-4, and all of the outlets are controlled by one 120 volt "trigger cable". You can plug the "trigger cable" into a standard 24 hour timer or lighting controller. The MLC-4 features four standard 240 volt style (NEMA 6-15) outlets, which your ballasts are plugged into. The MLC4a uses 120 volt style (NEMA 5-15) outlets which allows for running your ballasts at 240 volts without having to change out your ballast power cord. An integrated timer option is available which replaces the "trigger cable", allowing you to control your MLC with the built-in time clock. NOTE: Make sure ballasts are wired/configured for 240 Volt operation before energizing them. Rated at 30 amps @ 240 volts. |
| 4-120 Light Load Switch W Internal 0-20 Minute On Delay |
| 4-120 Lighting Load Switch w Internal 0-20 Minute On Delay This switching module will switch up to four 600 watt lights using a low power 120Vac trigger cord. An internal On-delay timer can be set to prevent hot bulb startups or set to sequentially turn on groups of up to four lights. This unit is powered by 120Vac and delivers the same to the connected equipment. |
Green Air 8 Light Timer - 240 Volts Model LT8-240 The LT8-240 provides eight 5 amp 240 volt outlet receptacles, each capable of powering up to 1000 watts of lighting equipment |
| Solatel LP 120S and LP240S Lamp Pro Timers These easy to use timers have a single select knob that clicks to any of 16 time settings. Settings include an accelerated 18 hour day cycle running ON 6 hours / OFF 12 hours. Thirteen normal 24 hour day settings cover ON 8 / OFF 16 to ON 20 / OFF 4 in one hour increments. Continuously ON and OFF settings are also included. The Lamp Pro sequences two outlets on, 20 seconds later the next two, and 20 seconds later the final two. This reduces electrical problems. Turn off has a 5 second delay. The LP-120S (120 volt 15 amp) uses standard 120 volt type outlets and power cord plug. The LP-240S (240 volt 30 amp) has 240 volt outlets and an 8 foot power cord with unterminated wires. It can control up to six 1000 watt fixtures. |
CAP HLC-2 15 Minute ON Delay Light Control The HLC-2 is designed to protect your expensive HID lights from "Hot Starts." A hot start occurs whenever your lights are turned OFF and then back ON before the lamp is allowed to cool off. Hot starts caused by power outages reduce your lamp's life and intensity. When the HLC-2 is connected to your lights, it will sense a power interruption and start a 15 minute time delay to keep the lights from trying to re-fire during the cool down period. The HLC-2 can also be used to delay other devices from starting for 15 minutes when power is applied. Rated for 15 amps @ 120 volts. |
| CAP HLC-1 High Temperature Shut-Down |
CAP HLC-1 High Temperature Shut-Down The HLC-1 is used as a high temperature shutdown by plugging your lights into the outlet and setting the maximum temperature that your growing environment can sustain. If this setting is exceeded, your lights will turn off. This is cheap insurance for your garden. The HLC-1 can also be used as a heating thermostat. Connect your heating equipment to the heating outlet, and then set the temperature that you wish to maintain. If the temperature falls below your setting, the heating outlet is activated. Comes with a 3' remote temperature sensor. Rated for 15 amps @ 120 volts |
| Need a product you don't see. Write us about it, if we stock it you'll get it at our cost & shipping. |
CAP MLC-16 & MLC-24 Lighting Relays
|
| CAP MLC-16 & MLC-24 Lighting Relays Models: |
| Green Air 8 Light Timer - 240 Volts Model LT8-240 |
| CAP HLC-2 15 Minute ON Delay Light Control |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |
| |
 |